I also have a zen4 cpu.

The 30 second boots are memory training. The motherboard is basically training itself on how the DDR5 memory modules respond on every signal wire and it can be inordinately slow depending in memory amount. For whatever reason, AMD DDR5 systems are slower at it than comparable Intel DDR5 systems.

Update your BIOS to the latest version then enabled “Memory Context Restore”. The bios will then save the last training results and stop taking 30 seconds to start up.

Is yours a new AM5 socket based AMD system by any chance?

Being from a very rural area: guns are tools. They provide self defense against wildlife and crazy humans when you’re miles outside of law enforcement coverage, they are pest control, and they are a humane way of euthanasia when a farm animal is suffering.

And like most other tools, such as drills, post hole augers, machine lathes, tractors, cars, etc… they can maim and kill indiscriminately when used incorrectly or maliciously. But you cannot simply ban or remove the tool from everywhere because it is still serves a very important purpose. Can they be more controlled, education made mandatory, more stringent confiscation rules in the case of people with mental illness? Yes, and probably should. But you will never eliminate the firearm completely.

I am prepared to recieve the hate and downvotes for providing a measured, reasonable response.

Often a combination of temp too high, not enough retraction, or water contaminated filament.

If the plastic in the hot end is too hot it will keep “running” out of the nozzle after retraction and you’ll get strings. Similarly if you don’t retract enough to actually pull plastic out of the nozzle during a rapid move, it will want to keep pushing thru. This is supported by the little blobs it leaves on that angled surface corner its travelling to when stringing, thats excess material squeezing out during its rapid moves then being left on that wall.
And if there’s water in your filament all bets are off on how it’ll behave.

215 is pretty warm for that esun PLA especially if you’re using the stock brass nozzle, try bumping that down to 205 or even 200, and increase your retraction speed and distance settings in prusaslicer a tiny amount (0.1mm distance, 2mm/s speed at a time until you see improvement is plenty)

Use a temperature calibration tower to test things out.

can’t wait to see the hexbear response to this one

Try SoulSeek

Aside from hard science and engineering degrees where the technical knowledge is a foundation for what you’ll learn in industry, a college degree is simply a piece of paper that says “I received a balanced education and have my life together enough to focus, manage time, and complete tasks reliably for 4 years straight.” Rarely do you ever use most of the knowledge you gained in college besides the aforementioned life management skills.

You not responding because you don’t actually have any logical arguments lmaoooooo

Get better material, this trolling is lower effort than I’ve ever seen

Darth Stupidus

Unless you are on a private tracker that have seed ratio requirements, there is zero obligation to hold onto a torrent until you have a 1:1 ratio. Its only a recommendation, and very much an “Honor Among Thieves” situation.
Feel free to delete the wrong torrent and re-download the right one. If you feel bad about it, keep the right one until a 2:1 ratio so you maintain balance in the world. :)

Heeeeere comes the hexbear brigade!

I do modelling as my day job and spend some time hobby modeling on the side with educational edition Autodesk software. I could probably whip that up for you in a couple days. PM me and let’s exchange some details.

Considering how much shit I see retail workers go through, this… honestly seems like a rational response. I’m sure it will immediately turn into middle managers using it to abuse employees of course though.

Yes, PLA creeps ridiculously fast in hot conditions it is unsuitable for use in any environment over 35C tbh.

PETG is better but will still warp/fade over time if it’s exposed to the sun, and likely need replacing.

You need to be printing in ABS or ideally ASA if you want all-weather resistant cases. Which means now your printer needs an enclosure and ventilation…

I reported extremely obvious spam repost bots and also got a permaban for “abusing reports”. Fuck em, they want rhe garbage content to overrun their site, they’re gonna get it.

Get. Rid. Of. Their. Router.

ISP provided networking routers are inherently garbage. They don’t want users messing with that, because your average user doesn’t even know what the fuck an ethernet cable is and will break everything by fucking around in it.

Run your own router and put theirs into modem only mode with routing and wifi disabled. If that’s not an option ask their tech support if you can buy your own DOCSIS/fiber modem (or whatever hardware you use) and return their hardware. If they also don’t allow that… well, switch or just suck it and deal with it while the ISP rubs their nipples some more.

Doing the lord’s work. What a shitfest of a modlog, real winner this guy is

Edit: dear God he keeps MAKING MORE. This dude seriously needs to get a life or something

Ayo I’m in the screenshot letsa fucking GOOOOOOOOOO-

For context, Bungiefan_ak has no fewer than 4 alts that I’ve seen (all on different instances with the same username) and has spent his time on [email protected] continuously spamming heavily transphobic, homophobic, and objectifying sexist “memes”. Just about every one of his alts is now banned but I’m sure more will pop up.

Now, why the fuck he cares so much about pirates at this point, I haven’t a clue…

2GB of memory is fine for openWRT. Routing is surprisingly light tbh, consider that most all home/SOHO routers run integrated SoC’s with <256MB of memory.

routing speed is more dependent on CPU +cache speed

i’d eat my boot if a residential ISP let you run your own SFP fiber module. they have to pretty tighttly control those things to keep signal levels right and have wavelengths in the right spots. plus they’ll need to upstream reconfigure it somewhat frequently as the local network changes and if it’s not their hardware, they’ll get mad.

unfortunately “pretty good” is not “guaranteed”, which is often what I need for both work and school. I tried to make myself use only libre options for like a week and just about every assignment I opened was broken in some way or another so I always ended up back in Word.

I’ll still use the libreoffice options if i’m, say, already logged into my Linux install and don’t want to bother going back to Windows. But since I get Office for free thru work and school, and so does everyone else, well… I just use it.