Your partner is correct. Please do not drive anymore for the health of everyone else…

You might have been thinking about openSCAD not openCAD?

Both sides can talk at the same time during VOIP calls. While Simplex can send audio or other files you can also tap the phone icon in your contact. This will make a regular phone call or video call with two way communication. For me, calls have worked the best out of other open source apps other than Signal. Only problem I have had was echo when using speaker phone. Regular calls work fine.

If you were asking about the network layer how things work. There are small packets of information going in both directions. Dropped packets will cause short lost audio. But normally all the small packets are put together into a continuous two way communication.

I think they are just looking for a supplier. Check out partsavatar.ca I have used them many times. There is also thewrenchmonkey.ca haven’t used them yet.

Yes it is going to be difficult with rural places. I feel like (PHEV) plug in hybrids with electric only modes have been skipped over… There is certain area that would benefit from them. I could do 80% of my driving on electric and gas only when needed. There is a couple models I’m looking at for my next car, if only I can find one used for a good price. 😂

But tucked away inside this building is a room that’s heavily insulated and packed with powerful heaters and coolers. It can be cranked down to 20 degrees Fahrenheit, or up to 95.

20F is -6.67C, That is not very cold… We can get months of anywhere between -25C to -40C without the wind chill here. I would be interested in more tests at cold tempatures. Last we need is people expecting more than they are going to get. I would just expect range to be cut in half but either way I would much rather have an electric car.

Good points. I just wanted to add to make sure you turn the flow control knob tightly off every time you are done with it. And never leave an empty can on it, change it quickly. I leave a can on mine permanently so its always ready to go. Can use a tiny amount then then close the flow control knob off. I have let mine sit for over 6 months with no issues. I only clean it rarely when I don’t have a fresh can to put on. I have only gone though two foam pistols/guns in 15 years. I would never use the normal cans again. Way to much waste.

Is the room temp high enough with no cold drafts? I live in a cold area and have had print problems with the room being to cold.

Yep that’s the idea. Not actually sure if its preventing anything… But it hasn’t come back. Its in the shower so I don’t care. Finish washing up and spray the shower with cleaner when im done. 😂

Strange story for you… I had very bad athletes foot for many years. All the off the shelf powders and creams didn’t help at all. Someone told me to pee on my feet to cure it, I didnt believe them but tried it anyways. Worked amazingly quickly. Occasionally I do it still but not all the time. Haven’t had athletes foot in over 25 years… I’m so sorry for the story. 😂

How well are those glass panes sealed to the wood? Could silicone the panes in. Doubt it would help you go lower, but I’m curious how much the dehumidifier runs after it gets to 35% to keep it there? I didnt realize they even made dehumidifiers that small, might have to look at them. 🙂

I dont know much about OpenWRT so dont pay to much attention to me.

I doubt 20ms of extra latency would make much of a noticeable difference. Though its odd its higher now. Does it change, get higher and lower? Are you cable links actually connected at 1000Mbps? Or are some connected at only 100? Can you verify the connection speed?

I have seen IP conflicts with do some weird things depending on hardware. Have a good look to make sure something didn’t get missed with static IPs And Your DHCP pool.

I have been using Kivy and like it a lot for simple stuff. Its cross platform Python GUI.

https://kivy.org/

Your right. I read your post wrong! Sorry.

They do the same thing with grid storage batteries and I hate it. “Our battery lasts 20 hours!” Think it was a better unit like watts per 4 hours but media and marketing mess with it.

i.e. “anti anti-fascist”

You mean anti-fascist, not the double negative? That might be an important typo. 🙂

Thanks for testing that! I thought it might work but I was wrong. Guess people will have to do one to RiMusic first then Kreate. Hopfully that still works…

Thats what I have been using. Its based off RiMusic which was based off ViMusic.

https://github.com/knighthat/Kreate

Just adding a note. People should be able to backup your music in ViMusic or RiMusic and restore in Create. They seem to use the same database. Though I havent tried directly from ViMusic to Kreate. I went from ViMusic to RiMusic to Kreate.